CH-92509 Screen Silk Spot UV varnish 紫外線硬化網版印刷油操作步驟 (BOPP膜 + Spot UV 網版印花) 1. 混合：為獲得較佳的附著性，需將 CH-92509 (http://www.shm.com.tw/92509.htm) 網版印刷油Silk Screen UV varnish 與硬化劑以攪拌機或震盪器混合10分鐘，混合比例100：7。由於硬化劑會與CH-92509進行化學反應，故混合完後需在一小時內使用完畢。 2.網印：依所需塗佈厚度選擇不同網目數之網板(膜厚越厚網目數越小250~ 300 course/inch)，將網版印刷油塗佈在BOPP膜上。 3.曝光：UV燈管120W/cm，速度15M/min(曝光能量約250~300 mJ/cm2) 4.硬化：網版印刷油與硬化劑會緩慢進行化學反應，約需48小時可獲得極佳的附著性。 CH-92509 +7% Harden Pharmaceutical

CH-92509 Screen Silk Spot UV varnish
The ultraviolet ray hardens the Silk Screen prints the oil operating sequence
(BOPP Film + Spot UV Silk Screen printing)

1. Mix: In order to get better adhering to, need silk screen print oil UV varnish with harden pharmaceutical mix 10 minutes with mixer or person who shake CH-92509 (http://www.shm.com.tw/92509.htm ),
mixed proportion 100: 7. Because hardenning the pharmaceutical will carry on the chemical reaction with CH-92509 , so need to finish using within an hour after finishing mixing.

2.The Silk Screen is printed: Choose with mesh board that eye count in accordance with necessary coating thickness (the mesh eye count around 250 ~ 300 course/inch ), print the silk screen the oil coating on the BOPP film surface.

3.Expose: UV light is in charge of 120W/cm, speed 15M/min (exposes energy and invites 250~300 mJ/cm2 )

4. Harden: Print the oil and harden the pharmaceutical and will carry on the chemical reaction slowly , can get the extremely good adhering to to nearly need in 48 hours in silk screen .

CH-92509 Screen Silk Spot UV varnish 紫外線硬化網版印刷油操作步驟 (PP板材 + Spot UV網版印花) 1. 混合：為獲得較佳的附著性，需將 CH-92509 (http://www.shm.com.tw/92509.htm) 網版印刷油Silk Screen UV varnish 與硬化劑以攪拌機或震盪器混合10分鐘，混合比例100：7。由於硬化劑會與CH-92509進行化學反應，故混合完後需在一小時內使用完畢。 2.網印：依所需塗佈厚度選擇不同網目數之網板(膜厚越厚網目數越小250~ 300 course/inch)，將網版印刷油塗佈在PP板上。 3.曝光：UV燈管120W/cm，速度15M/min(曝光能量約250~300 mJ/cm2) 4.硬化：網版印刷油與硬化劑會緩慢進行化學反應，約需48小時可獲得極佳的附著性。 CH-92509 +7% Harden Pharmaceutical

CH-92509 Screen Silk Spot UV varnish
The ultraviolet ray hardens the Silk Screen prints the oil operating sequence
(PP Sheet + Spot UV Silk Screen printing)

1. Mix: In order to get better adhering to, need silk screen print oil UV varnish with harden pharmaceutical mix 10 minutes with mixer or person who shake CH-92509 (http://www.shm.com.tw/92509.htm ),
mixed proportion 100: 7. Because hardenning the pharmaceutical will carry on the chemical reaction with CH-92509 , so need to finish using within an hour after finishing mixing.

2.The Silk Screen is printed: Choose with mesh board that eye count in accordance with necessary coating thickness (the mesh eye count around 250 ~ 300 course/inch ), print the silk screen the oil coating on the BOPP film surface.

3.Expose: UV light is in charge of 120W/cm, speed 15M/min (exposes energy and invites 250~300 mJ/cm2 )

4. Harden: Print the oil and harden the pharmaceutical and will carry on the chemical reaction slowly , can get the extremely good adhering to to nearly need in 48 hours in silk screen .